Technical Specifications
Geometry
| Small | Medium | Large | XL | XXL | |
|---|---|---|---|---|---|
| Rider Height | 5'1"-5'6" | 5'5"-5'10" | 5'9"-6'1" | 6'0"-6'4" | 6'3"-6'9" |
| Effective Top Tube Length | 582mm | 603mm | 625mm | 650mm | 678mm |
| Seat Tube Length | 385mm | 415mm | 445mm | 475mm | 505mm |
| Seat Tube Angle | 76°/71° | 76°/71° | 76°/71° | 76.5°/71° | 77°/72° |
| Chain Stay Length | 436mm | 436mm | 436mm | 436mm | 436mm |
| Bottom Bracket Drop | 34.2mm | 34.2mm | 34.2mm | 34.2mm | 34.2mm |
| Bottom Bracket Height | 345mm | 345mm | 345mm | 345mm | 345mm |
| Head Tube Angle | 65.5° | 65.5° | 65.5° | 65.5° | 65.5° |
| Wheel Base | 1175mm | 1198mm | 1222mm | 1256mm | 1293mm |
| Head Tube Length | 90mm | 96mm | 104mm | 115mm | 145mm |
| Axle to Crown | 551mm | 551mm | 551mm | 551mm | 551mm |
| Fork Offset | 44mm | 44mm | 44mm | 44mm | 44mm |
| Trail | 123mm | 123mm | 123mm | 123mm | 123mm |
| Stack | 604mm | 610mm | 618mm | 635mm | 650mm |
| Reach | 431mm | 451mm | 471mm | 498mm | 528mm |
| Standover | 717mm | 720mm | 728mm | 742mm | 760mm |
Frame Specs
Wheel Size |
29" |
Front Travel |
140mm |
Rear Travel |
130mm |
Shock Spec |
210mm X 50mm |
Axles |
177x12x1.0 |
Seatpost Diameter |
31.6mm, 34.9mm Seat Collar |
Max Seatpost Insertion Depth |
300mm ALL SIZES |
Rear Brake |
180mm post mount/203mm max rotor size |
Rear Tire Clearance |
29" x 2.6" |
Bottom Bracket |
73mm BSA English Threaded |
Max Chainring |
36T Round / 34T Oval, 55mm Chainline |
Tapered Headtube |
IS42 upper / IS52 Lower |
Bottle Bosses |
2 Sets of bosses. 1 set located along top of down tube. 1 set located along bottom of down tube. Size XXL has an additional set underneath the top tube |
Suspension
Support
We do not – We found the leverage curve of our bikes leaves the shock very tunable. We have successfully set up riders from 95 lbs. to well over 230 lbs.
We only recommend the Push ELEVENSIX coil shock.
The shock size is 210x50mm. The mounting hardware size is 25x8mm.
The Rascal was designed to use a 140mm fork with a 44mm offset and an axle-to-crown length of 547-551mm. You may use a 150mm fork with a maximum axle-to-crown length of 561mm.
No you cannot and while we love experimenting and innovation, doing so will void the warranty.
30% is the recommended amount of sag to run on the Rascal. Start with 30% then you can adjust +/- 5% for a slightly softer or firmer ride.
RockShox Super Deluxe Shock has 2 spacers.
Rockshox Lyrik Fork has 1 volume spacer.
Fox Float X has a 0.4 volume spacer.
Fox Float 36 fork has 2 volume spacers.
No we do not recommend doing this. The Rasal was designed to be ridden as a full 29er and performs at its best in this configuration.
The Rascal uses a BSA 73mm threaded bottom bracket.
The Rascal features ISCG-05 tabs. This is a common mounting standard for chainguides and bash guards that you can find from great companies like MRP, OneUp, and E13.
36T ROUND / 34T OVAL.
| Torque Specifications | |
|---|---|
| Pivot #1 | 15 Nm - Apply grease to axle shaft (DO NOT apply grease to threads) |
| Pivot #2 | 15 Nm - Apply grease to axle shaft (DO NOT apply grease to threads) |
| Pivot #3 | 15 Nm - Apply grease to axle shaft (DO NOT apply grease to threads) |
| Pivot #4 | 10 Nm |
| Pivot #5 | 15 Nm - Apply grease to axle shaft (DO NOT apply grease to threads)Front triangle and rear triangle must be assembled before upper link is connected to rear triangle. |
| Rear Shock Bolt / Forward Shock Bolt | 15 Nm Rear / 10Nm Front. Apply titanium anti-seize to threads on rear shock bolt. |
| SRAM Universal Derailleur Hanger | 25 Nm. *UDH Hanger is left-hand threaded |
| Revel UDH Rear Axle | 13 Nm |
| Seat Clamp | 5 Nm |
| Cable Clamp | 2 Nm |
Required Tools for Basic Service
» 1x 4mm Hex Key
» 1x 5mm Hex Key
» 1x 6mm Hex Key
» 1x 8mm Hex Key
» Torque Wrench
» Grease
» Titanium Anti-Seize Compound
» *Bearing Puller (Slide Hammer)
-12mm Bearing Collet
-15mm Bearing Collet
» *Bearing Press
-12mm ID Bearing Drift (Ensure largest diameter on drift measures less than or equal to 21mm) [ Used on Pivot 1, Pivot 2, Pivot 3 & Pivot 5
]- 15mm ID Bearing Drift (Ensure largest diameter on drift measures less than or equal to 24mm) [ Used on Pivot 4 ]
» *If performing full bearing replacement
| 310-10021-0063 | Pivot #1/#2 Axle x2 |
| 310-10021-0060 | Pivot #1/#2/#4 Axle Nut x3 |
| 100-BEA21-0001 | Pivot #1/#2/#4 Axle Nut x3 |
| 310-10021-0058 | Pivot #1/#2/#4 Pivot Spacer x5 |
| 310-10021-0062 | Pivot #1/#2 Axle Spacer x2 |
| 310-10021-0064 | Pivot #3/#5 Axle Nut x4 |
| 310-10021-0066 | Pivot #3/#5 Axle x4 |
| 310-BEA18-0106 | BOLU Bearing 6801 P3/P5 x4 |
| 310-10021-0088 | Pivot #3/#5 Axle Spacer x4 |
| 310-10021-0091 | Pivot #4 Axle Collet x1 |
» For detailed view and part information on specific pivots, please download the tech manual.
» Ensure all bolts are torqued to spec listed in this manual and on bolt head.
» All bolts are right hand threaded but have hex profiles on either end. If turning the bolt from the threaded side, turning counter clockwise will tighten the bolt
» Bolts come with Nylock patch installed. This serves the function of thread looker and can be reused for multiple installations. Verify condition of patch before assembly. If patch looks worn or damaged add Blue Loctite 243.
» It is easier to tighten linkage assembly to torque once it has been fully assembled. Similarly it is easiset to break bolts free when linkage is fully assembled.
» All images shown in exploded views of pivots correspond to exploded view on Page 4 of Tech Manual.




